Arccaptain Protective Gear
\nFR Balaclava Full Face Mask for Welding
\nWhether you're running MIG beads for hours, grinding down welds, or working a full fabrication shift, unprotected skin on your face, neck, and shoulders is a liability. The Arccaptain FR Balaclava is built to eliminate that risk without slowing you down. Soft knitted flame-resistant fabric, optimized mesh ventilation, a three-panel helmet-ready construction, and extended shoulder coverage — all in a balaclava that weighs just 7 oz.
\nDesigned specifically for welders and fabricators who need real protection and all-day comfort, not just a thin neck gaiter that rides up and leaves your shoulders exposed.
\nProduct Features
\nBuilt for the Weld. Worn All Day.
\nSoft, Breathable & Comfortable
\nMade from soft knitted flame-resistant fabric with optimized mesh ventilation zones, this welding balaclava feels comfortable against your skin from the first hour to the last. Heat and moisture escape through the mesh rather than building up against your face — making long welding and grinding sessions far more manageable.
\nLightweight — Only 7 oz
\nAt just 7 oz, you'll barely notice it's there. Delivers reliable warmth and flame protection without the bulk or fatigue of heavier FR hoods. Ideal for year-round use — keeps you warm in a cold winter garage and ventilated enough for a hot summer shop.
\n3-Panel Helmet-Ready Design
\nThe three-panel head construction sits flat and smooth under auto-darkening welding helmets and hard hats. No bunching at the crown, no pressure points at the forehead — just a clean, secure fit that stays in place from the first strike to the last bead.
\nExtended Shoulder Coverage
\nThe enlarged shoulder design shields your neck and upper shoulders from sparks, spatter, and grinding debris — the areas most often left exposed by standard balaclavas. Less time adjusting gear, more time welding. Fewer burns on the neck at the end of the shift.
\nGlasses & Goggle Opening
\nDedicated openings for safety glasses and grinding goggles let eyewear users get a clean, comfortable fit without the balaclava riding up or distorting the seal. Works with standard ANSI-rated safety glasses, prescription glasses, and most grinding goggle styles.
\nTwo-in-One Quick Switch
\nThe layered two-in-one look lets you shift quickly between welding, grinding, and general work without removing the balaclava. Mesh ventilation around the mouth improves airflow during active grinding where heat builds fast — reconfigure in seconds for each task.
\nDesigned For
\nFrom the Shop Floor to the Job Site
\nThis FR welding hood is purpose-built for anyone working around arc flash, spatter, and abrasive debris on a regular basis.
\n- \n
- \nMIG & TIG Welders Full-face spark and spatter protection with heat-venting mesh so you stay focused on the puddle, not your comfort. \n
- \nStick & Flux-Core Welders Guards against the heavy spatter that comes with high-amperage stick and flux-core processes — exactly where exposed skin gets burned most often. \n
- \nAngle Grinder & Cut-Off Wheel Users Shields the neck, face, and shoulders from abrasive metal debris and grinding sparks without limiting your range of motion. \n
- \nFabricators & Ironworkers Comfortable enough to wear under a hard hat for extended fabrication and ironwork shifts without causing fatigue or heat buildup. \n
- \nHome Shop & Garage Welders Lightweight and breathable enough for hobbyist weekend projects — professional-grade protection without the heavyweight price or bulk. \n
Product Gallery
\nSee Every Detail
\n![\"Arccaptain](\"https://cdn.shopify.com/s/files/1/0613/8458/9369/files/FR_Balaclava_Full_Face_Mask_1_c21a81bd-7f09-42ad-bcec-419744e84c7e.jpg?v=1773910689\")
![\"FR](\"https://cdn.shopify.com/s/files/1/0613/8458/9369/files/FR_Balaclava_Full_Face_Mask_7.png?v=1773910689\")
![\"FR](\"https://cdn.shopify.com/s/files/1/0613/8458/9369/files/FR_Balaclava_Full_Face_Mask_2.png?v=1773910690\")
![\"FR](\"https://cdn.shopify.com/s/files/1/0613/8458/9369/files/FR_Balaclava_Full_Face_Mask_3.png?v=1773910689\")
![\"FR](\"https://cdn.shopify.com/s/files/1/0613/8458/9369/files/FR_Balaclava_Full_Face_Mask_4.png?v=1773910686\")
![\"FR](\"https://cdn.shopify.com/s/files/1/0613/8458/9369/files/FR_Balaclava_Full_Face_Mask_5.png?v=1773910688\")
![\"FR](\"https://cdn.shopify.com/s/files/1/0613/8458/9369/files/FR_Balaclava_Full_Face_Mask_6.png?v=1773910688\")
\nFit Guide
\nSize Guide (US Standard)\n
\nMeasure around the widest part of your head — just above the ears and eyebrows — using a soft tape measure. If you fall between sizes, size up for a more relaxed fit under a welding helmet or hard hat.
\n| Size | \nRecommended Head Circumference | \nFits Head Circumference | \nLength | \n
|---|---|---|---|
| S | \nUp to 22.6 in | \n18.9 – 22.8 in | \n16.5 in | \n
| M | \nUp to 23.4 in | \n20.5 – 24.4 in | \n17.3 in | \n
Pro tip: Most welders with a head circumference between 22 and 23 inches prefer the M for a looser fit that doesn't compress under a welding helmet headgear band.
\nCare Instructions
\nKeep the FR Rating Intact
\nProper laundering is critical for maintaining the flame-resistant properties of the fabric. Follow these guidelines to get the full service life out of your balaclava:
\n- \n
- Machine wash in cold water on a gentle cycle. \n
- Tumble dry on low heat or air dry flat. \n
- \nDo not use bleach or fabric softener — both degrade flame-resistant fiber treatments over time. \n
- Do not iron directly on the fabric. If pressing is needed, use a low-heat setting with a pressing cloth. \n
- Inspect for damage, holes, or worn areas before each use. Compromised fabric reduces protection. \n
FR Balaclava Full Face Mask for Welding Work
Arccaptain Protective Gear
FR Balaclava Full Face Mask for Welding
Whether you're running MIG beads for hours, grinding down welds, or working a full fabrication shift, unprotected skin on your face, neck, and shoulders is a liability. The Arccaptain FR Balaclava is built to eliminate that risk without slowing you down. Soft knitted flame-resistant fabric, optimized mesh ventilation, a three-panel helmet-ready construction, and extended shoulder coverage — all in a balaclava that weighs just 7 oz.
Designed specifically for welders and fabricators who need real protection and all-day comfort, not just a thin neck gaiter that rides up and leaves your shoulders exposed.
Product Features
Built for the Weld. Worn All Day.
Soft, Breathable & Comfortable
Made from soft knitted flame-resistant fabric with optimized mesh ventilation zones, this welding balaclava feels comfortable against your skin from the first hour to the last. Heat and moisture escape through the mesh rather than building up against your face — making long welding and grinding sessions far more manageable.
Lightweight — Only 7 oz
At just 7 oz, you'll barely notice it's there. Delivers reliable warmth and flame protection without the bulk or fatigue of heavier FR hoods. Ideal for year-round use — keeps you warm in a cold winter garage and ventilated enough for a hot summer shop.
3-Panel Helmet-Ready Design
The three-panel head construction sits flat and smooth under auto-darkening welding helmets and hard hats. No bunching at the crown, no pressure points at the forehead — just a clean, secure fit that stays in place from the first strike to the last bead.
Extended Shoulder Coverage
The enlarged shoulder design shields your neck and upper shoulders from sparks, spatter, and grinding debris — the areas most often left exposed by standard balaclavas. Less time adjusting gear, more time welding. Fewer burns on the neck at the end of the shift.
Glasses & Goggle Opening
Dedicated openings for safety glasses and grinding goggles let eyewear users get a clean, comfortable fit without the balaclava riding up or distorting the seal. Works with standard ANSI-rated safety glasses, prescription glasses, and most grinding goggle styles.
Two-in-One Quick Switch
The layered two-in-one look lets you shift quickly between welding, grinding, and general work without removing the balaclava. Mesh ventilation around the mouth improves airflow during active grinding where heat builds fast — reconfigure in seconds for each task.
Designed For
From the Shop Floor to the Job Site
This FR welding hood is purpose-built for anyone working around arc flash, spatter, and abrasive debris on a regular basis.
- MIG & TIG Welders Full-face spark and spatter protection with heat-venting mesh so you stay focused on the puddle, not your comfort.
- Stick & Flux-Core Welders Guards against the heavy spatter that comes with high-amperage stick and flux-core processes — exactly where exposed skin gets burned most often.
- Angle Grinder & Cut-Off Wheel Users Shields the neck, face, and shoulders from abrasive metal debris and grinding sparks without limiting your range of motion.
- Fabricators & Ironworkers Comfortable enough to wear under a hard hat for extended fabrication and ironwork shifts without causing fatigue or heat buildup.
- Home Shop & Garage Welders Lightweight and breathable enough for hobbyist weekend projects — professional-grade protection without the heavyweight price or bulk.
Product Gallery
See Every Detail
Fit Guide
Size Guide (US Standard)
Measure around the widest part of your head — just above the ears and eyebrows — using a soft tape measure. If you fall between sizes, size up for a more relaxed fit under a welding helmet or hard hat.
| Size | Recommended Head Circumference | Fits Head Circumference | Length |
|---|---|---|---|
| S | Up to 22.6 in | 18.9 – 22.8 in | 16.5 in |
| M | Up to 23.4 in | 20.5 – 24.4 in | 17.3 in |
Pro tip: Most welders with a head circumference between 22 and 23 inches prefer the M for a looser fit that doesn't compress under a welding helmet headgear band.
Care Instructions
Keep the FR Rating Intact
Proper laundering is critical for maintaining the flame-resistant properties of the fabric. Follow these guidelines to get the full service life out of your balaclava:
- Machine wash in cold water on a gentle cycle.
- Tumble dry on low heat or air dry flat.
- Do not use bleach or fabric softener — both degrade flame-resistant fiber treatments over time.
- Do not iron directly on the fabric. If pressing is needed, use a low-heat setting with a pressing cloth.
- Inspect for damage, holes, or worn areas before each use. Compromised fabric reduces protection.
Arccaptain Protective Gear
FR Balaclava Full Face Mask for Welding
Whether you're running MIG beads for hours, grinding down welds, or working a full fabrication shift, unprotected skin on your face, neck, and shoulders is a liability. The Arccaptain FR Balaclava is built to eliminate that risk without slowing you down. Soft knitted flame-resistant fabric, optimized mesh ventilation, a three-panel helmet-ready construction, and extended shoulder coverage — all in a balaclava that weighs just 7 oz.
Designed specifically for welders and fabricators who need real protection and all-day comfort, not just a thin neck gaiter that rides up and leaves your shoulders exposed.
Product Features
Built for the Weld. Worn All Day.
Soft, Breathable & Comfortable
Made from soft knitted flame-resistant fabric with optimized mesh ventilation zones, this welding balaclava feels comfortable against your skin from the first hour to the last. Heat and moisture escape through the mesh rather than building up against your face — making long welding and grinding sessions far more manageable.
Lightweight — Only 7 oz
At just 7 oz, you'll barely notice it's there. Delivers reliable warmth and flame protection without the bulk or fatigue of heavier FR hoods. Ideal for year-round use — keeps you warm in a cold winter garage and ventilated enough for a hot summer shop.
3-Panel Helmet-Ready Design
The three-panel head construction sits flat and smooth under auto-darkening welding helmets and hard hats. No bunching at the crown, no pressure points at the forehead — just a clean, secure fit that stays in place from the first strike to the last bead.
Extended Shoulder Coverage
The enlarged shoulder design shields your neck and upper shoulders from sparks, spatter, and grinding debris — the areas most often left exposed by standard balaclavas. Less time adjusting gear, more time welding. Fewer burns on the neck at the end of the shift.
Glasses & Goggle Opening
Dedicated openings for safety glasses and grinding goggles let eyewear users get a clean, comfortable fit without the balaclava riding up or distorting the seal. Works with standard ANSI-rated safety glasses, prescription glasses, and most grinding goggle styles.
Two-in-One Quick Switch
The layered two-in-one look lets you shift quickly between welding, grinding, and general work without removing the balaclava. Mesh ventilation around the mouth improves airflow during active grinding where heat builds fast — reconfigure in seconds for each task.
Designed For
From the Shop Floor to the Job Site
This FR welding hood is purpose-built for anyone working around arc flash, spatter, and abrasive debris on a regular basis.
- MIG & TIG Welders Full-face spark and spatter protection with heat-venting mesh so you stay focused on the puddle, not your comfort.
- Stick & Flux-Core Welders Guards against the heavy spatter that comes with high-amperage stick and flux-core processes — exactly where exposed skin gets burned most often.
- Angle Grinder & Cut-Off Wheel Users Shields the neck, face, and shoulders from abrasive metal debris and grinding sparks without limiting your range of motion.
- Fabricators & Ironworkers Comfortable enough to wear under a hard hat for extended fabrication and ironwork shifts without causing fatigue or heat buildup.
- Home Shop & Garage Welders Lightweight and breathable enough for hobbyist weekend projects — professional-grade protection without the heavyweight price or bulk.
Product Gallery
See Every Detail
Fit Guide
Size Guide (US Standard)
Measure around the widest part of your head — just above the ears and eyebrows — using a soft tape measure. If you fall between sizes, size up for a more relaxed fit under a welding helmet or hard hat.
| Size | Recommended Head Circumference | Fits Head Circumference | Length |
|---|---|---|---|
| S | Up to 22.6 in | 18.9 – 22.8 in | 16.5 in |
| M | Up to 23.4 in | 20.5 – 24.4 in | 17.3 in |
Pro tip: Most welders with a head circumference between 22 and 23 inches prefer the M for a looser fit that doesn't compress under a welding helmet headgear band.
Care Instructions
Keep the FR Rating Intact
Proper laundering is critical for maintaining the flame-resistant properties of the fabric. Follow these guidelines to get the full service life out of your balaclava:
- Machine wash in cold water on a gentle cycle.
- Tumble dry on low heat or air dry flat.
- Do not use bleach or fabric softener — both degrade flame-resistant fiber treatments over time.
- Do not iron directly on the fabric. If pressing is needed, use a low-heat setting with a pressing cloth.
- Inspect for damage, holes, or worn areas before each use. Compromised fabric reduces protection.
Original: $19.99
-65%$19.99
$7.00Description
Arccaptain Protective Gear
FR Balaclava Full Face Mask for Welding
Whether you're running MIG beads for hours, grinding down welds, or working a full fabrication shift, unprotected skin on your face, neck, and shoulders is a liability. The Arccaptain FR Balaclava is built to eliminate that risk without slowing you down. Soft knitted flame-resistant fabric, optimized mesh ventilation, a three-panel helmet-ready construction, and extended shoulder coverage — all in a balaclava that weighs just 7 oz.
Designed specifically for welders and fabricators who need real protection and all-day comfort, not just a thin neck gaiter that rides up and leaves your shoulders exposed.
Product Features
Built for the Weld. Worn All Day.
Soft, Breathable & Comfortable
Made from soft knitted flame-resistant fabric with optimized mesh ventilation zones, this welding balaclava feels comfortable against your skin from the first hour to the last. Heat and moisture escape through the mesh rather than building up against your face — making long welding and grinding sessions far more manageable.
Lightweight — Only 7 oz
At just 7 oz, you'll barely notice it's there. Delivers reliable warmth and flame protection without the bulk or fatigue of heavier FR hoods. Ideal for year-round use — keeps you warm in a cold winter garage and ventilated enough for a hot summer shop.
3-Panel Helmet-Ready Design
The three-panel head construction sits flat and smooth under auto-darkening welding helmets and hard hats. No bunching at the crown, no pressure points at the forehead — just a clean, secure fit that stays in place from the first strike to the last bead.
Extended Shoulder Coverage
The enlarged shoulder design shields your neck and upper shoulders from sparks, spatter, and grinding debris — the areas most often left exposed by standard balaclavas. Less time adjusting gear, more time welding. Fewer burns on the neck at the end of the shift.
Glasses & Goggle Opening
Dedicated openings for safety glasses and grinding goggles let eyewear users get a clean, comfortable fit without the balaclava riding up or distorting the seal. Works with standard ANSI-rated safety glasses, prescription glasses, and most grinding goggle styles.
Two-in-One Quick Switch
The layered two-in-one look lets you shift quickly between welding, grinding, and general work without removing the balaclava. Mesh ventilation around the mouth improves airflow during active grinding where heat builds fast — reconfigure in seconds for each task.
Designed For
From the Shop Floor to the Job Site
This FR welding hood is purpose-built for anyone working around arc flash, spatter, and abrasive debris on a regular basis.
- MIG & TIG Welders Full-face spark and spatter protection with heat-venting mesh so you stay focused on the puddle, not your comfort.
- Stick & Flux-Core Welders Guards against the heavy spatter that comes with high-amperage stick and flux-core processes — exactly where exposed skin gets burned most often.
- Angle Grinder & Cut-Off Wheel Users Shields the neck, face, and shoulders from abrasive metal debris and grinding sparks without limiting your range of motion.
- Fabricators & Ironworkers Comfortable enough to wear under a hard hat for extended fabrication and ironwork shifts without causing fatigue or heat buildup.
- Home Shop & Garage Welders Lightweight and breathable enough for hobbyist weekend projects — professional-grade protection without the heavyweight price or bulk.
Product Gallery
See Every Detail
Fit Guide
Size Guide (US Standard)
Measure around the widest part of your head — just above the ears and eyebrows — using a soft tape measure. If you fall between sizes, size up for a more relaxed fit under a welding helmet or hard hat.
| Size | Recommended Head Circumference | Fits Head Circumference | Length |
|---|---|---|---|
| S | Up to 22.6 in | 18.9 – 22.8 in | 16.5 in |
| M | Up to 23.4 in | 20.5 – 24.4 in | 17.3 in |
Pro tip: Most welders with a head circumference between 22 and 23 inches prefer the M for a looser fit that doesn't compress under a welding helmet headgear band.
Care Instructions
Keep the FR Rating Intact
Proper laundering is critical for maintaining the flame-resistant properties of the fabric. Follow these guidelines to get the full service life out of your balaclava:
- Machine wash in cold water on a gentle cycle.
- Tumble dry on low heat or air dry flat.
- Do not use bleach or fabric softener — both degrade flame-resistant fiber treatments over time.
- Do not iron directly on the fabric. If pressing is needed, use a low-heat setting with a pressing cloth.
- Inspect for damage, holes, or worn areas before each use. Compromised fabric reduces protection.
